Fix DirecTV remote not working

Channel:
Subscribers:
15,200
Published on ● Video Link: https://www.youtube.com/watch?v=grigvXGxVz8



Duration: 1:48
8 views
1


Here's how to DirecTV remote not working.

i. Here are the steps to reset a DirecTV remote and receiver:

To reset the DirecTV remote:

1. Locate the red reset button on the back of the remote near the top.

2. Use a straightened paperclip to press and hold the red reset button for 10-15 seconds until the light on the remote turns on.

3. Once the light turns on, release the reset button. The remote will be reset and re-paired with your DirecTV receiver.

To reset the DirecTV receiver:

1. Press and hold the red reset button on the receiver itself (usually located behind the small door on the front panel).

2. Hold the button down continuously for 10-15 seconds.

3. When the receiver restarts, the reset is complete. This will reset all settings to factory default.

4. Go through the startup setup prompts on your TV screen to reprogram channels and other preferences.

5. Re-pair your remote by pressing the mute and enter buttons together until the remote light flashes twice.

Doing both a remote and receiver reset can help resolve a lot of functionality issues like lost signal, pixelation, remote lag, etc.

ii. There are a few potential sources of signal interference that can affect a smart TV remote:

- Other remotes - Infrared remotes from other devices like cable boxes, streaming players, etc. can sometimes cause interference with a smart TV remote, especially if pointed towards the TV sensor. Keep other remotes away when using the smart TV remote.

- Fluorescent lighting - The flickering of fluorescent bulbs can emit infrared light that interferes with IR remote signals. This tends to be worse with older CFL bulbs. Make sure bulbs are not directly facing the TV sensor.

- Sunlight/windows - Bright sunlight and natural infrared light from windows can overwhelm a TV sensor. Closing blinds or curtains can help if this is an issue.

- Device pairing issues - If the smart remote is not properly paired or synced to the TV, interference and lag can occur. Re-pair the remote by pressing number buttons simultaneously.

- Low batteries - Weak batteries in the remote can cause signal issues. Replace batteries if remote has shortened range.

- Obstructed sensor - If furniture, frames, or other objects are blocking the IR sensor on the TV, the signal will be disrupted. Make sure there is a clear line-of-sight.

- Plasma TV interference - Plasma TVs tend to emit a lot of infrared radiation, which can interfere with IR remotes. This technology is being phased out though.

- Defective remote or sensor - In rare cases, a faulty remote or IR receiver sensor can cause interference problems.

So in summary - other remotes, lighting, batteries, and physical obstructions are the most common sources of smart TV remote signal issues.

iii. Here are the steps to check what mode your DirecTV remote is in and change it if needed:

1. Turn on the TV and DirecTV receiver.

2. Locate the four mode buttons at the top of the remote - TV, AV1, AV2, and DIRECTV.

3. Press and hold the DIRECTV button until the light at the top of the remote flashes twice. This indicates you're in DirecTV mode.

4. If the light doesn't flash after holding the DIRECTV button, press and hold one of the other mode buttons (TV, AV1, AV2) until the light flashes twice.

5. Once in DirecTV mode, you can change the remote to control other devices by pressing and holding the corresponding mode button (like TV for your television).

6. The light will flash twice when changing between modes.

7. Make sure to test channel changing and volume works in the new mode. You may need to program or pair the remote with the device.

8. Always remember to switch back to DirecTV mode when going to control your satellite receiver.

Tip: Pressing the small enter/clear button in the center of the arrow keys will flash the light to show the current mode.

Learn more@ https://www.youtube.com/c/ITGuides/search?query=DirecTV.