TEARDOWN BioScrypt Fingerprint Reader L-1 IDENTITY 4GFXS V-Flex 4G (S) w/Secugen Sensor
8BioScrypt's 4GFXS 4G V-Flex Biometric Fingerprint Reader Base Model with Secugen Sensor is the best choice when looking for the power and versatility of a V-Station, while still requiring a compact form factor device. This is the page for the Bioscrypt 4GFXS Base Model, which is for Single-Factor Fingerprint Authentication only. If you want a Prox Card Reader integrated into the 4G V-Flex 4GFXS than visit our Bioscrypt 4GFXSP 4G V-Flex page. If you want an iClass Contactless Smart Card Reader integrated, visit our Bioscrypt 4GFXSH 4G V-Flex page. Prepare to experience the ultimate in convenience. Forget about PINs or cards to gain access to secure areas, all you need is your finger! Decrease executive and HR expenses dramatically, while quickly providing employees with access to restricted areas with the Bioscrypt 4GFXS. Despite its size, the Bioscrypt 4GFXS 4G V-Flex still provides a very large template capacity at 10,000 in 1:N; 500,000 in 1:1, field replaceable sensors, backwards compatibility, Standalone Door Access Control (SDAC) Capabilities, plus other great benefits. The 4G V-Flex doesn't sacrifice speed either, as it still searches 6,000 templates a second, ensuring your employees will be granted access in seconds and with support for the newest communication standards in IP Connectivity, you'll be able to reduce maintenance costs by utilizing existing IT infrastructure. Security Administrators who need a compact device but still require strong biometric capabilities and deployment flexibility choose the 4G V-Flex as their Access Control System solution.
4G V-Flex (S)
Overview
The 4G V-Flex(S) is a standalone fingerprint reader. When used with Mercury-Security hardware and Access It! Universal’s Biometric option the 4G V-Flex(S) requires the use of an external reader. The external reader will initiate the 4G V-Flex’s verification polling upon a valid card transaction. Since an external reader is required, two reader ports must be used for each 4G V-Flex(S) installation of solution. Both the external reader and 4G V-Flex (S) must be installed on the same EP controller.
The overall procedure when presenting a card at the external reader is as follows:
A Card or PIN is presented at the external reader.
The EP controller recognizes that the external reader requires a biometric verification.
The EP controller initializes the 4G V-Flex and prompts for a finger to be presented.
The fingerprint read is sent to the EP controller.
The EP controller compares the fingerprint read to the stored template within its database.
If fingerprint comparison matches, the EP controller grants access to the external reader.
Access It! Universal Licensing
The following licensing option must be enabled within the Access It! Universal dongle and is a system wide license.
Biometric Support - Yes
Installation Requirements
The 4G V-Flex (S) requires the following:
Access It! Universal min s/w v4
Access It! Universal optional Biometric license enabled
L1 Identity Solutions SecureAdmin software
4G V-Flex(S) min f/w 4.1.11.0.2.a2.0
EP Series Controllers min f/w 1.176
Supported SIOs
MR-50 min f/w 1.52.4
MR-52 min f/w 1.55.0
MR-51E min f/w 1.4.9
Wiring
External Reader
External Reader Reader Port
DC+ VO
DC- GND
D1 D1
D0 D0
LED LED
BZR BZR
.
4G V-Flex
4G V-Flex Reader Port
DC+ External power source
DC- External power source
RS-485A D1
RS-485B D0
SGND GND
The 4G V-Flex must be powered through PoE or a separate power supply.
Refer to the L-1 Installation Guide for specific power information.
SecureAdmin Software
Prior to making any changes, the 4G V-Flex must already be registered in SecureAdmin. Contact L1/Morpho for any registration inquiries.
Log into SecureAdmin
Select Device Settings
Select the 4G V-Flex
Select the Communication tab
Set the Device ID to 0
If two 4G V-Flex units are on the same SIO, they need to be uniquely addressed 0 and 1.
Set the Host Protocol to RS-485
Set the Host Baud Rate to 38400
Click Apply
Select the Biometrics tab
Within the Device mode field, select Verify
Select the Template Type 1:1 TEM
In the Multi-User Verification set the Number of Users to 1
Click Apply
Select the Miscellaneous tab
In the Send verification Result section, ensure none of the checkboxes are checked
Check the box Activate Verification Polling Mode
Click Yes at the SecureAdmin warning dialog box
Select Weigand Only for the Initiate Verification By field
Click Apply
Close SecureAdmin
Access It! Universal.NET 5.2
Within Access It! Universal.NET navigate to the Hardware menu
Select SCPs
Edit the EP controller the Biometric reader is installed under
Select the Biometrics tab
Select Edit Biometric Types
Select New
Within the Biometric type description, enter the name Morpho 4G
From the Biometric template type, select Bioscrypt/Morpho Fingerprint
Select the Default security threshold
The default threshold determines the ratio of false