Tutorial For YouTube Subscriber Counter

Channel:

InterlinkKnight

Subscribers:

30,900

Published on November 6, 2020 4:39:21 PM ● Video Link: https://www.youtube.com/watch?v=B4L0lnCfrlI

Category:

Tutorial

Duration: 8:50

1,715 views

62

These are the instructions on how to make a YouTube Subscriber Counter like the one I show on this video: https://youtu.be/Vnc-PjzcPHQ
Sponsored by PCBWay - Full feature custom PCB prototype service: https://www.pcbway.com/

- Instructables Project Page: https://www.instructables.com/id/YouTube-Subscriber-Counter/
- Thingiverse Project Page: https://www.thingiverse.com/thing:4520059

Parts:
- E-Paper Display 7.5 inch 3 colors (black, white and red) 800x480 https://amzn.to/30LZ8Gn
- ESP-WROOM-32E, ESP-WROOM-32D or ESP-WROOM-32 bare module (not a development board) https://amzn.to/2AJ4uaL or you can use a development board if you plan to use it with a plugged power supply https://amzn.to/3gi5yTI
- UART USB to TTL serial converter https://www.ebay.com/itm/362514706922
- Battery Holder AAx4 https://amzn.to/34tiOi0
- Shadow Box 6x8inch with an inside space of at least 1.1inch/28mm deep https://amzn.to/3avcKYB
- Frame Mat 6x8 for 4x6 pictures. I find that it's cheaper to buy a frame that comes with the mat that trying to buy a mat separately https://amzn.to/3S3XS9w
- Resistors 1K, 10K x2, 300K, 470K https://amzn.to/2A2gHE6
- Electrolytic Capacitors 100µF 16V x2 - It's important to buy good quality capacitors and that they are small enough to fit the enclosure that you are going to use. This is what I choose: https://www.digikey.com/products/en?keywords=Ruby...
- Ceramic Capacitor 0.1µF https://amzn.to/3xfAL0N
- Push Buttons 6x6x4.3mm x2 https://amzn.to/3zi76WD
- Voltage Regulator with low dropout voltage and low quiescent current. The best I found is the HT7333-A https://amzn.to/3538b5K
- NPN Transistor S8050 https://amzn.to/2yk6HYV
- PCB 5x7cm - You have two options: either buy a prototype PCB made for ESP32 https://amzn.to/3cvSsB6 so you have to make all the connections yourself, or order a custom PCB on PCBWay for $5 with my gerber files.
- M3 HEX screws of different sizes (12mm, 8mm, 4mm) and nuts https://amzn.to/3e44FMp
- M2x6mm HEX screws https://amzn.to/3fdb0Ff
- Washers 3x7mm x8 https://amzn.to/3fvwehO
- 2.54mm male and female pin header https://amzn.to/2xYcOlK
- Printable Sticker Paper https://amzn.to/3wbS6HR
Recommended tools for this project:
- Loctite Liquid Professional Super Glue https://amzn.to/2N7d1He
- Wera 1.5-10mm Hex-Plus Key https://amzn.to/2N4gXYW
- 6-inch Zip Ties https://amzn.to/2N6QCcQ
- Scotch Painter's Tape https://amzn.to/2AMfeFb

Note: As an Amazon Associate I earn from qualifying purchases.


Files:
- Arduino sketch: https://drive.google.com/file/d/1tJhNqMnc8c1OAT0KLpODREte7QLVTnTt/view?usp=sharing
- 3D Printed Parts: https://drive.google.com/file/d/19Vge7TitSMUwSJiOd0lG9u1ZDs7zgaUI/view?usp=sharing
- Gerber files for custom PCB: https://drive.google.com/file/d/1YFNecsEBCawaHT2a-yuT8cP4e48WrQKR/view?usp=sharing
- BOM for PCB: https://drive.google.com/file/d/1x66G8-Xzb3y3FEJR8YZJiUcUNKyD1U1G/view?usp=sharing
- Stickers: https://drive.google.com/file/d/1K-dbW-8a-SY7SGF0wzXZwnEKx7H6Hvak/view?usp=sharing


Website: https://www.interlinkknight.com/
Patreon: https://www.patreon.com/InterlinkKnight/