How to Configure Static Routing on Cisco Router in GNS3 | SYSNETTECH Solutions
26This video shows you how to configure Static Routing on Cisco Routers using GNS3.
✅ S U B S C R I B E ► http://goo.gl/8d0iG9
✅ Article ► https://www.sysnettechsolutions.com/en/configure-static-routing-on-cisco-router-in-gns3/
To configure #Static #Routing (Static Route):
Step 1: If you have not done the #GNS3 installation before, please refer to the following videos to install it on Windows, Linux, and even macOS High Sierra.
Windows ➦ https://www.youtube.com/watch?v=Fp_2NjI4W58
Linux ➦ https://www.youtube.com/watch?v=WDxXx9fMQAQ
macOS ➦ https://www.youtube.com/watch?v=ITg_TQibjAQ
Step 2: After performing the installation, add two Cisco Routers and Cisco Switches to the workspace.
Step 3: If you have previously added the Cisco Router IOS image to the program, browse the following video.
Video ➦ https://www.youtube.com/watch?v=ErzQ_Lcx9uo
Step 4: It is better to use VMware Workstation virtual machines for Static Routing configuration. To use VMware virtual machines, you can browse the following video.
Video ➦ https://www.youtube.com/watch?v=SwE9VaZ7lXQ
Step 5: Before creating VMs, specify two different network addresses. For example;
A) 192.168.5.0/24
B) 192.168.10.0/24
Step 6: Configure the IP configuration of VMs according to the network ranges you specify.
Step 7: Add virtual machines to GNS3 and connect them to Cisco Switches.
Step 8: Connect the Routers with the Serial Cable.
Step 9: After connecting the Switches to the Routers, run all the devices.
Step 10: Assign IP addresses to the FastEthernet and Serial interfaces of Routers and no shutdown their ports.
Step 11: To configure or enable Static Route on the Router in GNS3, apply the following commands as an example.
For Cisco Router R1:
R1(config)# ip route 192.168.10.0 255.255.255.0 10.1.1.2
For Cisco Router R2:
R1(config)# ip route 192.168.5.0 255.255.255.0 10.1.1.1
Step 12: Ping to network 2 from network 1 and check the network connection.
Step 13: You will see that they can communicate computers at two different locations with Static Routing.
Step 14: You can use show commands to check the config on Routers.
Step 15: Watch the entire video for the rest of the process.
Step 16: Don't forget to subscribe to our YouTube channel for more videos on Cisco CCNA training with GNS3!
────────BEST PRODUCT FOR CISCO TRAINING────────
✅ Buy ► http://bit.ly/CCNARoutingandSwitching
───────────────RELATED VIDEOS───────────────
➊ How to Configure RIP
➦ https://www.youtube.com/watch?v=839dk8lYhFU
➋ How to Configure RIP Version 2
➦ https://www.youtube.com/watch?v=1tsGWuCtEIw
➌ How to Configure Cloud
➦ https://www.youtube.com/watch?v=DVokiwWzlxk
➍ How to Configure EIGRP
➦ https://www.youtube.com/watch?v=rJC3UERvdnQ
➎ How to Configure OSPF
➦ https://www.youtube.com/watch?v=gFMvgpDSzlI
───────────────FOLLOW US───────────────────
✔ Facebook
➦ https://www.facebook.com/SysnettechSolutions/
✔ Twitter
➦ https://twitter.com/SysnettechS/
✔ Pinterest
➦ https://www.pinterest.com/SysnettechS/
✔ Instagram
➦ https://www.instagram.com/sysnettech_solutions/
✔ LinkedIn
➦ https://linkedin.com/in/tolqabaqci/
███████████████████████████████████████████